Open pit

During this paper, in order to identify the priority of consideration between the problems of “mining method selection” and “determining transition depth from open-pit to underground mining” an accurate procedure is introduced step by step. First, it is essential to specify if an ore deposit that potentially will have mined by a combined method of open-pit and underground mining. In this case, optimal final open-pit limit and depth must be initially determined. After that, if the rest of deposit below open-pit limit is economically considerable, it is necessary to select the most adequate underground method with emphasis on the high production rate and low cost methods. Then, it is necessary to determine optimal transition depth from open-pit to underground mining considering a crown pillar immediately below open-pit mining. Finally, the procedure with its algorithm was used for an iron ore deposit with the combined mining potential.

An appropriate open pit slope design is the one that considers both the safety and cost aspects to minimize waste excavation. Open pit slope design of Ajabanoko iron ore deposit, Nigeria was carried out using DIPS and SLOPE/W mine softwares. Compass clinometer and Geographic Positioning System (GPS) were used to determine the dip, dip direction and location respectively of joints on the iron ore deposit and this serves as an input data in the slope design. Fifty-two dip/dip direction values were plotted using DIPS mine software. The factor of safety of the designed slope was determined using limit equilibrium method included in the slope SLOPE/W program. In order to calculate the factor of safety for the designed slopes, inputs parameters, namely unit weight of the rock mass, internal friction angle and cohesion were used in the SLOPE/W program. The obtained result indicates that slope angles with orientation of 44/071, 50/270, 61/359, 46/178 were considered safe for the eastern, western, northern and southern section of the deposit respectively. The slope design carried out shows a factor of safety that varies from a lower limit of 2.89 to an upper limit of 3.84, and this indicates safe slopes in all sections of the deposit.

During this paper, in order to identify the priority of consideration between the problems of "mining method selection" and "determining transition depth from open-pit to underground mining" an accurate procedure is introduced step by step. First, it is essential to specify if an ore deposit that potentially will have mined by a combined method of open-pit and underground mining. In this case, optimal final open-pit limit and depth must be initially determined. After that, if the rest of deposit below open-pit limit is economically considerable, it is necessary to select the most adequate underground method with emphasis on the high production rate and low cost methods. Then, it is necessary to determine optimal transition depth from open-pit to underground mining considering a crown pillar immediately below open-pit mining. Finally, the procedure with its algorithm was used for an iron ore deposit with the combined mining potential.

During this paper, in order to identify the priority of consideration between the problems of "mining method selection" and "determining transition depth from open-pit to underground mining" an accurate procedure is introduced step by step. First, it is essential to specify if an ore deposit that potentially will have mined by a combined method of open-pit and underground mining. In this case, optimal final open-pit limit and depth must be initially determined. After that, if the rest of deposit below open-pit limit is economically considerable, it is necessary to select the most adequate underground method with emphasis on the high production rate and low cost methods. Then, it is necessary to determine optimal transition depth from open-pit to underground mining considering a crown pillar immediately below open-pit mining. Finally, the procedure with its algorithm was used for an iron ore deposit with the combined mining potential.

This is the author’s version of a work that was submitted/accepted for pub-lication in the following source: Liu, Shi Qiang & Kozan, Erhan (2012) An interactive planning and schedul-ing framework for optimising pits-to-crushers operations. Industrial Engi-

Implementing stable final pit walls in open pit mines during the open pit design phase and mine exploitation has become one of the most important concerns of mining engineers in recent years. Failure of mine walls can potentially cause loss of life, roads blocks, and damage to mining machinery, temporarily or permanently halt production at the face and in the worst case scenario, close the mine. Thus, the role of creating stable mine walls is crucial to safety and general operations of mines and any effort to optimize this process has great economic value for mine operators. This paper aims to illustrate the technical aspects of use of the successful presplit blasting method in metal open pit mines. It also shows that using this approach not only increases safety in mines through wall stabilization, but also will boost economic profits by savings in stripping ratio. In this regard, appropriate practical concepts for designing the drilling and blasting patterns and the role of select...

During this paper, in order to identify the priority of consideration between the problems of “mining method selection” and “determining transition depth from open-pit to underground mining” an accurate procedure is introduced step by step. First, it is essential to specify if an ore deposit that potentially will have mined by a combined method of open-pit and underground mining. In this case, optimal final open-pit limit and depth must be initially determined. After that, if the rest of deposit below open-pit limit is economically considerable, it is necessary to select the most adequate underground method with emphasis on the high production rate and low cost methods. Then, it is necessary to determine optimal transition depth from open-pit to underground mining considering a crown pillar immediately below open-pit mining. Finally, the procedure with its algorithm was used for an iron ore deposit with the combined mining potential.