Instituto Universitario de Plaguicidas y Aguas

A method has been developed for the sensitive and selective determination of cyromazine and its metabolite melamine in chard samples. Both compounds are small polar basic molecules, making their determination at residue levels complicated. The method involves an extraction procedure with phosphate buffer and methanol using high-speed blender, the addition of tridecafluoroheptanoic acid (TFHA) as ion-pair reagent and the injection of the five-fold diluted extract on liquid chromatography coupled to electrospray tandem mass spectrometry (LC-ESI-MS/MS). The method has been validated for chard samples, spiked at 0.05 and 0.5 mg kg −1 . Quantification was carried out by using matrix-matched standards calibration and recoveries were satisfactory, with mean values for cyromazine of 103% and 93%, and relative standard deviations lower than 7%. In the case of melamine, recoveries were 89% and 86%, with relative standard deviations lower than 13%. A limit of quantification of 0.05 mg kg −1 was obtained for both compounds, with the limit of detection below 0.01 mg kg −1 . The method, with very little sample handling and good sensitivity, was applied to the rapid determination of low residue levels of these compounds in chards from field residue trials. All the quality controls included during the analysis were satisfactory with average recoveries of 92% and 78% for cyromazine and melamine, respectively.

The potential of gas chromatography / tandem mass spectrometry with triple quadrupole analyzer for determination of 12 polybrominated diphenyl ethers in human breast tissues has been investigated. After extraction with hexane, two purification procedures -automated normal-phase HPLC and solid phase extraction -were assayed. Both electron impact ionization, in selected reaction monitoring mode, and negative chemical ionization, in selected ion recording mode, were tested for the optimum determination of analytes. Isotopically labelled standards were added before extraction as surrogates:

This work describes the optimization, validation and application of an ultra-high-pressure liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) method for the quantification and confirmation of 11 compounds (atrazine, simazine, terbuthylazine, terbumeton, terbutryn and their main transformation products) in surface and wastewater samples. Several of these analytes are included in the list of priority substances in the framework on European Water Policy. The application of this method to water samples reveals that the most relevant transformation products (TPs) should be incorporated into current analytical methods to obtain a more realistic knowledge of water quality regarding pesticide contamination. TPs are generally more polar and mobile than parents and can be transported to the aquatic environment more easily than their precursors. This can explain their concentrations found in water, which in many cases are much higher than intact triazines. To efficiently combine UHPLC with MS/MS, a fast-acquisition triple quadrupole mass analyser was used. Working in selected reaction monitoring mode, up to three simultaneous transitions per compound were acquired, allowing a reliable quantification and confirmation at nanogram per litre levels.

Ultra-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS-MS) has been used for screening and quantification of 32 pesticides and metabolites in two fruit matrices. The compounds investigated belonged to different chemical families of insecticides, acaricides, fungicides, and herbicides; several metabolites were also included. Quantification was conducted using matrix-matched standards calibration; response was a linear function of concentration in the range tested (10-500 ng mL −1 ). The method was validated with blank samples of lemon and raisin spiked at 0.01 and 0.1 mg kg −1 , and recoveries were satisfactory, between 70 and 110%, for most of the pesticides tested and relative standard deviations were below 15% (n=5 at each spiking level). Excellent sensitivity resulted in limits of detection for all compounds well below 0.01 mg kg −1 , with the limit of quantification being validated at 0.01 mg kg −1 . The UPLC system generates narrow peaks (approx. 5 s), thus increasing peak height and improving sensitivity. This improved separation efficiency facilitates adequate resolution not only of the analytes but also of matrix interferences compared with conventional HPLC. The method developed could also resolve some geometric isomers. The main advantage of this approach is the high sample throughput achieved because of the short analysis time, which enables satisfactory separation of all the compounds in less than 5 min per sample.

In the present work, a study is reported of the potential of coupled-column liquid chromatography (LC) applied to the determination of triazine residues in environmental water samples. For this purpose, two different techniques have been compared: on-line trace enrichment followed by LC (SPE-LC) and coupled-column liquid chromatography (LC-LC). First, a completely automated liquid chromatographic method based on on-line trace enrichment in a prepacked precolumn and using diode array detection has been developed for the simultaneous tracelevel determination of six triazine herbicides (simazine, cyanazine, atrazine, terbumeton, terbuthylazine, and terbutryn) and the main atrazine metabolites (desisopropylatrazine, desethylatrazine, and hydroxyatrazine). After preconcentration parameters were optimized by testing two different sorbents (C 18 and PRP-1) in three cartridges with different dimensions, a sample volume of 100 mL was selected in order to achieve maximal solute preconcentration. Detection limits lower than 0.1 µg‚L -1 were obtained even for the most polar analyte (desisopropylatrazine), which presented recoveries of around 30%. The method was validated by means of recovery experiments in groundwater and surface water samples spiked with the analytes at different levels (0.2-2 µg‚L -1 ). Afterward, the procedure was successfully applied in a program for monitoring of triazine residues in surface water carried out in a wet area of Castelló n, Spain. Different triazine herbicides such as simazine, terbumeton, terbuthylazine, and terbutryn were identified and quantified. The identity of these compounds was confirmed by their absorption UV spectra and by GC/MS analysis. Finally, two rapid, sensitive, and selective procedures, previously developed in our laboratory for the trace-level determination of triazine compounds, both based on LC-LC, were compared with the former procedure. The SPE-LC approach showed a considerable improvement in the global sensitivity at the expense of a decrease in selectivity as well as in sample throughput. S0003-2700(98)00062-6 CCC: $15.00

In this work, a method has been developed for the ultrasensitive and selective determination of various regulated mycotoxins (aflatoxins G1, G2, B1, B2, M1, and ochratoxin A) in baby food commodities and milk, using ultra high pressure liquid chromatography (UHPLC) coupled to tandem mass spectrometry (MS/MS). The high sensitivity required for these compounds made necessary the application of a pre-concentration step based on solid phase extraction with immunoaffinity columns, after sample extraction with acetonitrile:water (80:20). Thanks to the fast high-resolution of UHPLC and the enhanced selectivity obtained with the triple quadrupole mass analyser in SRM mode, the chromatographic separation was achieved in only 4 min.

A detailed analytical study on trichlorfon residues in selected vegetables samples has been carried out, focused on the reliable quantification and confirmation of this compound, and on stability of residues under storage. As a consequence, a rapid and sensitive LC-ESI-MS/MS method has been developed for the determination of residues of this insecticide in kaki fruit (flesh and peel) and cauliflower samples. Extraction was performed with acetonitrile using a high-speed blender. After 4-fold dilution of the extract with water, 20 µL was directly injected in the LC-ESI-MS/MS system (triple quadrupole), using matrix-matched standards calibration for quantification. Under optimized MS/MS conditions, limit of detections between 0.006 and 0.013 mg/kg were reached, and a limit of quantification of 0.05 mg/kg was established, with a runtime of only 15 min. Recoveries from spiked blank samples at 0.05 and 0.5 mg/kg were in the range 83-101% with relative standard deviations lower than 10%. The method was applied to treated and untreated samples collected from field residues trials, using quality control samples analysis for the evaluation of the method. Despite the acquisition of two MS/MS transitions in selected reaction monitoring mode, the analysis of treated samples revealed the presence of a chromatographic peak close to the analyte that corresponded to a trichlorfon isobaric compound that shared the same MS/MS transitions. This unusual situation in LC-MS/MS-based procedures required the application of an efficient chromatographic separation to avoid this interference. All experiments have been made in compliance with the principles of Good Laboratory Practices (GLP) and following the European SANCO guidelines for pesticides residue analysis (PRA).

Solid-phase microextraction (SPME) is a relatively new technique that appears as a convenient and efficient extraction method in contrast with more complex techniques used for pesticide residue analysis based on liquid-liquid and solid-phase extraction. This extraction procedure involves the absorption of analytes into a polymeric film coated onto a fine silica fiber directly dipped in the aqueous sample. An SPME procedure for the determination of 12 organophosphorus pesticides in clean environmental water samples at low ng / ml concentration level has been developed by optimising variables involved in extraction and desorption. The absorption equilibrium has been estimated by mathematical treatment of the process using an expression that describes experimental absorption time profiles. The method was evaluated according to the reproducibility, linearity range and limits of detection using two different fiber coatings: 100 mm polydimethylsiloxane and 85 mm polyacrylate. The limits of detection obtained using nitrogen-phosphorus detection ranged between 0.01 and 0.2 ng / ml with relative standard deviations lower than 15% at the 1 ng / ml level. The method showed good linearity between 0.1 and 10 ng / ml with regression coefficients ranging between 0.97 and 0.999. Determination of organophosphorus pesticides in water samples in concentration below 0.1 ng / ml can be easily carried out with this fast, economic and solvent-free SPME procedure.

In this work, a multiclass screening method for organic contaminants in natural and wastewater has been developed and validated for qualitative purposes, i.e. to ensure the reliable and sensitive identification of compounds detected in samples at a certain level of concentration. The screening is based on the use of GC-TOF MS, and the sample procedure involves solid phase extraction with C 18 cartridges. Around 150 organic contaminants from different chemical families were investigated, including PAHs, octyl/nonyl phenols, PCBs, PBDEs and a notable number of pesticides, such as insecticides (organochlorines, organophosphorus, carbamates and pyrethroids), herbicides (triazines and chloroacetanilides), fungicides and several relevant metabolites. Surface water, ground water and effluent wastewater were spiked with all target analytes at three concentration levels (0.02, 0.1 and 1 g/L). Influent wastewater and raw leachate from a municipal solid waste treatment plant were spiked at two levels (0.1 and 1 g/L). Up to five m/z ions were evaluated for every compound. The identification criterion was the presence of, at least, two m/z ions at the expected retention time, measured at their accurate mass, and the accomplishment of the Q/q i intensity ratio within specified tolerances. The vast majority of compounds investigated were correctly identified in the samples spiked at 1 g/L. When analyte concentration was lowered down to 0.1 g/L the identification was more problematic, especially in complex-matrix samples like influent wastewater. On the contrary, many contaminants could be properly identified at the lowest level 0.02 g/L in cleaner matrices. The procedure was applied to the screening of water samples of different origin and matrix composition and allowed the detection of several target contaminants. A highly reliable identification could be carried out thanks to the sensitive full-spectrum acquisition at accurate mass, the high selectivity reached with the use of narrow-mass window extracted ion chromatograms, the low mass errors observed in the positive detections and the Q/q ratio accomplishment.

The potential of solid-phase extraction coupled on-line to liquid chromatography/electrospray tandem mass spectrometry (SPE-LC-ESI-MS/MS) has been investigated in this paper for the efficient sensitive quantification and confirmation of 16 antibiotics in water. The list of targeted analytes included 10 quinolones (oxolinic acid (OXO), nalidixic acid (NAL), flumequine (FLU), marbofloxacine (MAR), ofloxacine (OFLO), enrofloxacine (ENR), pefloxacine (PEF), ciprofloxacine (CIP), pipemidic acid (PIPE), norfloxacine (NOR)) and 6 penicillins (penicillin G (PEN), oxacillin (OXA), dicloxacillin (DIC), piperacillin (PIP), cloxacillin (CLO) and ampicillin (AMP)) that were determined in ground and surface water. The procedure is based on the injection of 9.8 mL of sample into the SPE-LC-MS/MS system and the measurement of antibiotics by selected reaction monitoring mode, using a triple quadrupole analyser. The method has been validated at realistic low concentrations that might be present in environmental water, i.e. 10 and 100 ng L −1 , obtaining recoveries between 74% and 123% with relative standard deviation lower than 14%. Matrix effects were not relevant in most of cases, except for ampicillin in surface water, where notable signal suppression was observed. The limits of detection were as low as 0.4-4.3 ng L −1 . The method developed allows the rapid screening and quantification of all the analytes selected by acquiring one MS/MS transition (normally the most sensitive) for each compound. It was applied to a number of actual surface and groundwater samples with several compounds being detected, mainly quinolones, at low ng L −1 levels. Special attention was given to the confirmation of compounds detected in water due to the difficulties of obtaining confident confirmation at low ng L −1 . This matter has been of growing concern in the last few years as reflected by recent papers and correspondence. The acquisition of several MS/MS transitions for each compound detected in a second independent analysis allowed the unequivocal confirmation of identity, avoiding reporting false-positives. Finally, the potential of QTOF instruments to confirm positive samples has also been evaluated and compared with triple quadrupole analysers.

The potential of ultra-high-pressure liquid chromatography (UHPLC) coupled to hybrid quadrupole timeof-flight mass spectrometry (QTOF-MS) for the screening and confirmation of antibiotics in water samples is illustrated in this paper. UHPLC presents several advantages over conventional liquid chromatography as it generates narrow peaks (increasing peak height and improving sensitivity) and reduces chromatographic runs. Regarding QTOF-MS, its increased mass resolution, high sensitivity in full-spectrum acquisition mode and mass accuracy, in both MS and MS/MS modes, make this technique ideal for the detection and reliable confirmation of organic contaminants in environmental samples. After a solidphase extraction using Oasis HLB cartridges, UHPLC-QTOF-MS has been applied in this work to several types of water samples (surface water and influent and effluent wastewaters). Several antibiotics were found in the samples, such as ofloxacin, ciprofloxacin, clarythromycin or erythromycin, among others. Moreover, the full spectrum data provided by TOF-MS acquisition has enabled searching for many other pharmaceuticals that could be present in the samples in a "post-target" way. This approach has allowed the detection and confirmation of paracetamol, omeprazole and codeine, among others. UPLC-QTOF-MS has been shown as an attractive and efficient hyphenated technique for the rapid detection and confirmation of pharmaceuticals in water with very little sample handling.

An existing method for the determination of glyphosate and its main metabolite aminomethylphosphonic acid (AMPA) in water has been improved. It is based on precolumn derivatization with the fluorescent reagent 9-fluorenylmethylcloroformate (FMOC) followed by large-volume injection in a coupled-column LC system using fluorescence detection (LC-LC-FD). The derivatization step was slightly modified by changing parameters such as volume and/or concentration of sample and reagents to decrease the limits of quantification (LOQ) of glyphosate and AMPA to 0.1 g/l. Additionally, the use of Amberlite ® IRA-900 for preconcentration of glyphosate, prior to the derivatization step, was investigated; the LOQ of glyphosate was lowered to 0.02 g/l. Drinking, surface and ground water spiked with glyphosate and AMPA at 0.1-10 g/l concentrations were analysed by the improved LC-LC-FD method. Recoveries were 87-106% with relative standard deviations lower than 8%. Drinking and ground water spiked with glyphosate at 0.02 and 0.1 g/l were analysed after preconcentration on the anion-exchange resin with satisfactory recoveries (94-105%) and precision (better than 8%).

The applications of solid-phase microextraction (SPME) for sample preparation in pesticide residue analysis are reviewed in this paper taking into account the different approaches of this technique coupled mainly to gas chromatography but also to high-performance liquid chromatography. A complete revision of the existing literature has been made considering the different applications divided according to the pesticide families (organochlorine, organophosphorus, triazines, thiocarbamates, substituted uracils, urea derivatives and dinitroanilines among others) and the sample matrices analysed which included environmental samples (water and soil), food samples and biological fluids. Details on the analytical characteristics of the procedures described in the reviewed papers are given, and new trends in the applications of SPME in this field are discussed.

Internal standard Environmental and waste water a b s t r a c t An ultra-high-pressure liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) method for the determination of 37 pesticides (herbicides, insecticides and fungicides) in environmental and wastewater has been developed. To efficiently combine UHPLC with MS/MS, a fast-acquisition triple quadrupole mass analyzer was used. This analyzer (minimum dwell time, 5 ms) allows acquiring up to three simultaneous transitions in the selected reaction monitoring mode for each compound assuring a reliable identification without resolution or sensitivity losses. A pre-concentration step based on solidphase extraction using Waters Oasis HLB cartridges (0.2 g) was applied with a 100-fold pre-concentration factor along the whole analytical procedure. The method was validated based on European SANCO guidelines using surface, ground, drinking and treated water (from an urban solid residues treatment plant) spiked at two concentration levels (0.025 and 0.1 g/L), the lowest having been established as the limit of quantification objective. The method showed excellent sensitivity, with instrumental limits of detection ranging from 0.1 to 7 pg. It was applied to environmental water samples (ground and surface water) as well as to samples of urban solid waste leachates (raw leachate and treated leachate after applying reversed osmosis) collected from a municipal treatment plant. Matrix effects have been studied in the different types of water samples analyzed, and several isotope-labelled internal standards have been evaluated as a way to compensate the signal suppression observed for most of the compounds studied, especially in wastewater samples. As a general remark, only those pesticides which response was corrected using their own isotope-labelled molecule, could be satisfactorily corrected in all type of samples, assuring in this way the accurate quantification in all matrix samples.

A multi-class method for the simultaneous quantification and confirmation of 47 pharmaceuticals in environmental and wastewater samples has been developed. The target list of analytes included analgesic and anti-inflammatories, cholesterol lowering statin drugs and lipid regulators, antidepressants, antiulcer agents, psychiatric drugs, ansiolitics, cardiovasculars and a high number (26) of antibiotics from different chemical groups. A common pre-concentration step based on solid-phase extraction with Oasis HLB cartridges was applied, followed by ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) measurement. All compounds were satisfactorily determined in just one single injection, with a chromatographic run time of only 10 min. The process efficiency (combination of the matrix effect and the extraction process recovery) for the 47 selected compounds was evaluated in nine effluent wastewater (EWW) samples, and the use of different isotope-labelled internal standards (ILIS) was investigated to correct unsatisfactory values. Up to 12 ILIS were evaluated in EWW and surface water (SW). As expected, the ILIS provided satisfactory correction for their own analytes. However, the use of these ILIS for the rest of pharmaceuticals was problematic in some cases. Despite this fact, the correction with analogues ILIS was found useful for most of analytes in EWW, while was not strictly required in the SW tested. The method was successfully validated in SW and EWW at low concentration levels, as expected for pharmaceuticals in these matrices (0.025, 0.1 and 0.5 g/L in SW; 0.1 and 0.5 g/L in EWW). With only a few exceptions, the instrumental limits of detection varied between 0.1 and 8 pg. The limits of quantification were estimated from sample chromatograms at the lowest spiked levels tested and normally were below 20 ng/L for SW and below 50 ng/L for EWW. The developed method was applied to the analysis of around forty water samples (river waters and effluent wastewaters) from the Spanish Mediterranean region. Almost all the pharmaceuticals selected in this work were detected, mainly in effluent wastewater. In both matrices, analgesics and anti-inflammatories, lipid regulators and quinolone antibiotics were the most detected groups.

The liquid chromatography tandem mass spectroscopy residue determination of compounds without any acidic or basic centers such as abamectin has been investigated. Several approaches regarding the interface used and adduct formation have been compared. The low acidity of the hydroxyl groups only made deprotonation feasible using the atmospheric pressure chemical ionization (APCI) interface. To obtain sufficient sensitivity for residue analysis, the Ion Sabre APCI interface was necessary. However, the sensitivity attained was lower than for monitoring adducts in positive ion mode. Using electrospray ionization, different adducts with Na ϩ , NH 4 ϩ , and Li ϩ were tested and compared. The best results were obtained for the ammoniated adduct in electrospray ionization (ESI) because of its high sensitivity and the presence of several product ions with similar abundance. The highest sensitivity was reached using an in-source fragment as precursor ion, leading to a limit of detection (LOD) of 2 g/L with low relative standard deviation. The relatively high abundance of other transitions allowed abamectin confirmation at concentrations close to the LOD (6 g/L). Alkali ions were found to be a suitable alternative to determine and confirm abamectin at residue levels. The [M ϩ Na] ϩ also presented various product ions with similar abundance, which allowed confirmation at LOD levels. However, this LOD was found to be almost four times higher than with [M ϩ NH 4 ] ϩ because of the poor sensitivity of the transitions obtained. Although the use of Li ϩ facilitated the fragmentation of the adduct [M ϩ Li] ϩ , with similar sensitivity to [M ϩ NH 4 ] ϩ , this fragmentation preferentially generated only one product ion, which did not allow confirmation at concentration levels lower than 15 g/L. The use of APCI for monitoring adducts was also feasible, but with less sensitivity. The sensitivity increased with the Ion Sabre APCI, although it was still five times lower than with ESI. Other adduct formers such as Co 2ϩ and Ni 2ϩ also were tested with unsatisfactory results. (J Am Soc Mass Spectrom 2005, 16, 1619 -1630

A rapid, sensitive and selective method has been developed for the direct determination of ethephon residues in vegetables (apple, cherry and tomato). Given the anionic character of ethephon, the use of ion-pairing liquid chromatography (LC) in combination with tandem mass spectrometry (MS/MS, triple quadrupole) allowed its direct determination in these matrices avoiding a derivatisation step and favouring the automation of the method. Samples were extracted with a mixture of dichloromethane/aqueous formic acid (pH 3) (1:1). Then, tetrabutylammonium acetate (TBA) was added as an ion-pairing reagent, and an aliquot of the aqueous extract was directly injected into the LC/MS/MS system. Quantification was performed with matrix-matched standards prepared from blank sample extracts. MS/MS measurements were made in the selected reaction monitoring (SRM) mode, using the most sensitive transition (m/z 107 > 79) for quantification, and up to four additional transitions for confirmation. Quantitative recoveries were obtained for all matrices (between 83% and 96%) at two concentration levels tested (0.05 and 0.5 mg/kg), with relative standard deviations lower than 9% in all cases. The addition of TBA directly into the sample extract contained in the injection vial was found sufficient to obtain satisfactory LC retention for the analyte. Under these conditions, the absence of ion-pairing reagent in the mobile phase minimised the ionisation suppression for ethephon in the MS source, leading to an increase in the sensitivity of the method and reaching limits of detection of 0.02 mg/kg for all matrices investigated. The acquisition of five specific MS/MS transitions for ethephon allowed the simultaneous and reliable quantification and confirmation of the analyte in the samples.