Selective plane illumination microscopy on a chip

Optics Express, 2017

Light sheet microscopy is a relatively new form of fluorescence microscopy that has been receiving a lot of attention recently. The strong points of the technique, such as high signal to noise ratio and its reduced photodamage of fluorescently labelled samples, come from its unique feature to illuminate only a thin plane in the sample that coincides with the focal plane of the detection lens. Typically this requires two closely positioned perpendicular objective lenses, one for detection and one for illumination. Apart from the fact that this special configuration of objective lenses is incompatible with standard microscope bodies, it is particularly problematic for high-resolution lenses which typically have a short working distance. To address these issues we developed sample holders with an integrated micromirror to perform single lens light sheet microscopy, also known as single objective single plane illumination microscopy (SoSPIM). The first design is based on a wet-etched silicon substrate, the second on a microfabricated polished polymer plug. We achieved an on-chip light sheet thickness of 2.3 μm (FWHM) at 638 nm with the polymer micromirror and of 1.7 μm (FWHM) at 638 nm with the silicon micromirror, comparable to reported light sheet thicknesses obtained on dedicated light sheet microscopes. A marked contrast improvement was obtained with both sample holders as compared to classic epi-fluorescence microscopy. In order to evaluate whether this technology could be made available on a larger scale, in a next step we evaluated the optical quality of inexpensive replicas from both types of master molds. We found that replicas from the polished polymer based mold have an optical quality close to that of the master component, while replicas from the silicon based mold were of slightly lower but still acceptable quality. The suitability of the replicated polymer based sample holder for single-lens light sheet microscopy was finally demonstrated by imaging breast cancer spheroids.

Nature Methods, 2007

We report that single (or selective) plane illumination microscopy (SPIM), combined with a new deconvolution algorithm, provides a three-dimensional spatial resolution exceeding that of confocal fluorescence microscopy in large samples. We demonstrate this by imaging large living multicellular specimens obtained in a three-dimensional cell culture. The ability to rapidly image large samples at high resolution with minimal photodamage provides new opportunities especially for the study of subcellular processes in large living specimens.

2019

We present cleared tissue Axially Swept Light-Sheet Microscopy (ctASLM), which achieves sub-micron isotropic resolution, high optical sectioning capability, and large field of view imaging (870×870 μm2) over a broad range of immersion media. ctASLM can image live, expanded, and both aqueous and organic chemically cleared tissue preparations and provides 2- to 5-fold better axial resolution than confocal or other reported cleared tissue light-sheet microscopes. We image millimeter-sized tissues with sub-micron 3D resolution, which enabled us to perform automated detection of cells and subcellular features such as dendritic spines.

Nature communications, 2017

Light-sheet fluorescence microscopy (LSFM) enables high-speed, high-resolution, and gentle imaging of live specimens over extended periods. Here we describe a technique that improves the spatiotemporal resolution and collection efficiency of LSFM without modifying the underlying microscope. By imaging samples on reflective coverslips, we enable simultaneous collection of four complementary views in 250 ms, doubling speed and improving information content relative to symmetric dual-view LSFM. We also report a modified deconvolution algorithm that removes associated epifluorescence contamination and fuses all views for resolution recovery. Furthermore, we enhance spatial resolution (to <300 nm in all three dimensions) by applying our method to single-view LSFM, permitting simultaneous acquisition of two high-resolution views otherwise difficult to obtain due to steric constraints at high numerical aperture. We demonstrate the broad applicability of our method in a variety of sample...

Micromachines, 2021

The recent advances in chip-size microscopy based on optical scanning with spatially resolved nano-illumination light sources are presented. This new straightforward technique takes advantage of the currently achieved miniaturization of LEDs in fully addressable arrays. These nano-LEDs are used to scan the sample with a resolution comparable to the LED sizes, giving rise to chip-sized scanning optical microscopes without mechanical parts or optical accessories. The operation principle and the potential of this new kind of microscope are analyzed through three different implementations of decreasing LED dimensions from 20 µm down to 200 nm.

Light sheet microscopy promises to revolutionize developmental biology by enabling live in toto imaging of entire embryos with minimal phototoxicity. We present detailed instructions for building a compact and customizable Selective Plane Illumination Microscopy (SPIM) system. The integrated OpenSPIM hardware and software platform is shared with the scientific community through a public website, thereby making light sheet microscopy accessible for widespread use and optimization to various applications.

Cold Spring Harbor protocols, 2014

In modern biology, most optical imaging technologies are applied to two-dimensional cell culture systems; that is, they are used in a cellular context that is defined by hard and flat surfaces. However, a physiological context is not found in single cells cultivated on coverslips. It requires the complex three-dimensional (3D) relationship of cells cultivated in extracellular matrix (ECM) gels, tissue sections, or in naturally developing organisms. In fact, the number of applications of 3D cell cultures in basic research as well as in drug discovery and toxicity testing has been increasing over the past few years. Unfortunately, the imaging of highly scattering multicellular specimens is still challenging. The main issues are the limited optical penetration depth, the phototoxicity, and the fluorophore bleaching. Light-sheet-based fluorescence microscopy (LSFM) overcomes many drawbacks of conventional fluorescence microscopy by using an orthogonal/azimuthal fluorescence arrangement with independent sets of lenses for illumination and detection. The basic idea is to illuminate the specimen from the side with a thin light sheet that overlaps with the focal plane of a wide-field fluorescence microscope. Optical sectioning and minimal phototoxic damage or photobleaching outside a small volume close to the focal plane are intrinsic properties of LSFM. We discuss the basic principles of LSFM and methods for the preparation, embedding, and imaging of 3D specimens used in the life sciences in an implementation of LSFM known as the single (or selective) plane illumination microscope (SPIM). TRADITIONAL OPTICAL IMAGING TECHNIQUES An understanding of modern developmental biology requires us to monitor the complex 3D relationship of cells, whether cultivated (e.g., in an ECM-based gel), in developing embryos, or in tissue sections (Pampaloni et al. 2007). However, the observation and the optical manipulation of multicellular biological specimens remains a challenge, principally for two reasons: • Such specimens are optically dense. They scatter and absorb light; thus, the delivery of the probing light and the collection of the signal light tend to become inefficient. • In addition to the fluorophores, many endogenous biochemical compounds absorb light and suffer phototoxicity, which can induce damage or can kill the specimen (Pampaloni et al. 2007). The situation is particularly dramatic in confocal fluorescence microscopy. Even when only a single plane is observed, the entire specimen is illuminated. Recording stacks of images along the optical z-axis thus illuminates the entire specimen once for each plane. Hence, cultured cells are illuminated 10-20 times and fish embryos are illuminated 100-300 times more often than they are observed. As we will see in the next section, this can be avoided by a simple change to the optical arrangement.

Scientific Reports, 2018

Selective plane illumination microscopy (SPIM) represents a preferred method in dynamic tissue imaging, because it combines high spatiotemporal resolution with low phototoxicity. The OpenSPIM system was developed to provide an accessible and flexible microscope set-up for non-specialist users. Here, we report Structured SPIM (SSPIM), which offers an open-source, user-friendly and compact toolbox for beam shaping to be applied within the OpenSPIM platform. SSPIM is able to generate digital patterns for a wide range of illumination beams including static and spherical Gaussian beams, Bessel beams and Airy beams by controlling the pattern of a Spatial Light Modulator (SLM). In addition, SSPIM can produce patterns for structured illumination including incoherent and coherent array beams and tiling for all types of the supported beams. We describe the workflow of the toolbox and demonstrate its application by comparing experimental data with simulation results for a wide range of illumin...

Cold Spring Harbor protocols, 2013

Ultramicroscopy (UM) is a powerful imaging technique that achieves precise and accurate three-dimensional (3D) reconstructions of intact macroscopic specimens with micrometer resolution. It was developed for specimens in the size range of ∼1-15 mm, such as whole mouse brains, mouse embryos, mouse organs, and Drosophila melanogaster. In UM, the specimen is illuminated perpendicular to the observation pathway by two thin counterpropagating sheets of laser light. UM is closely related to a growing family of comparable microscopy approaches based on light sheet illumination developed in recent years. This article presents an overview of light-sheet-based microscopy and describes the underlying physics of light sheet generation. The assembly of an "ultramicroscope" for investigating fixed chemically cleared tissue is described in detail, and the functions of the essential components, such as mechanics, camera, and objectives, are discussed. Finally, practical applications of UM...

PLoS ONE, 2014

We developed a multiple light-sheet microscopy (MLSM) system capable of 3D fluorescence imaging. Employing spatial filter in the excitation arm of a SPIM system, we successfully generated multiple light-sheets. This improves upon the existing SPIM system and is capable of 3D volume imaging by simultaneously illuminating multiple planes in the sample. Theta detection geometry is employed for data acquisition from multiple specimen layers. This detection scheme inherits many advantages including, background reduction, cross-talk free fluorescence detection and high-resolution at long working distance. Using this technique, we generated 5 equi-intense light-sheets of thickness approximately 7:5 mm with an inter-sheet separation of 15 mm. Moreover, the light-sheets generated by MLSM is found to be 2 times thinner than the state-of-art SPIM system. Imaging of fluorescently coated yeast cells of size 4+1 mm (encaged in Agarose gel-matrix) is achieved. Proposed imaging technique may accelerate the field of fluorescence microscopy, cell biology and biophotonics.