Academia.eduAcademia.edu

Outline

Title
Abstract
Introduction
Summary on Linear Motors
Conclusion
References
All Topics
Engineering
Electrical Engineering

Electrical motors in the lift systems: a review

Profile image of International Journal of Power Electronics and Drive SystemsInternational Journal of Power Electronics and Drive Systems

2024, International Journal of Power Electronics and Drive Systems (IJPEDS)

https://doi.org/10.11591/IJPEDS.V15.I3.PP1379-1386
visibility

…

description

8 pages

link

1 file

Abstract

This paper discussed a few type linear motors for lift systems applications. First, a few types of lift systems are generally presented. Based on these types of lift systems, the common actuators used to operate the lifts are compared and analyzed. Basically, in traditional lift systems, rotational motors are commonly employed as actuators. However, to achieve simpler lift systems, linear motors are utilized instead of rotational motors in direct drive systems. There are three types of linear motors usually being adopted which are linear induction motors (LIM), permanent magnets linear synchronous motors (PMLSM) and switched-reluctance linear synchronous motors (SRLSM). LIM exhibits a simple structure but relatively have low performance, while the SRLSM demonstrates a similar simplicity yet delivering improved performance compared to the LIM. On the other hand, the PMLSM, despite its high-performance capabilities, suffers from notable cogging.

Related papers

Force ripple and jerk minimisation in double sided linear switched reluctance motor used in elevator application
siamak masoudi

The linear switched reluctance motors (LSRMs) have many benefits such as simple structure, low cost, comparatively high force-to-mass ratio, and no need for mechanical rotary to linear motion converters. However, application of these motors is limited because of their force ripple. In this study, the LSRM is used in vertical motion and a new control strategy is proposed for reducing the force ripple. This method is based on instantaneous control of motor position, speed, phase current, and force. In order to realise the good motion quality of elevator, this study applies a speed profile based on minimum jerk model. Also, a new force distribution function is proposed that can properly distribute the total force among the phases. Using this function, phase currents can properly track the corresponding command currents and then, decrease undesirable ripples of output force considerably. The control system was implemented on a double sided four phase LSRM. Its performance is demonstrated by means of modelling and experimental results in elevator application.

View PDFchevron_right
An electromechanical implement lift system with position control for low horse power tractor
Abhisek kumar

Agricultural Engineering International Cigr Journal, 2014

Based on the output of software made in Visual Basic, an electromechanical implement lift system with position control was developed to maximize useful power of a low horse power (hp) tractor by replacing hydraulic system requiring higher power. It comprised of two lower links, one top link, two lift rods, one connecting rod and a power screw mechanism. The prototype was tested as per IS: 12224-1987 for recommended load of 150 kg on test frame and satisfactory results were found. The response time for lifting a load of maximum lifting capacity on test frame i.e. 116 kg and 110 kg for entire lifting range was found to be 71 s and 20.7 s for single start screw and triple start screw, respectively as compared to 44.7 s and 13.3 s for lowering the loads. The position control of the system was also tested and found satisfactory with no drop in the height for maximum lifting capacity. The developed system could save 88% of tractor input power compared to hydraulic system. Highlights • Design of an electromechanical implement lift system for low hp tractor. • Provision of position control system. • A single operator's switch could operate the system and preset the depth. • Saving of tractor input power by 88 % compare to hydraulic system.

View PDFchevron_right
Pole-changing motor for lift installation
Makhsud Bobojanov

E3S Web of Conferences, 2020

The Numerous lift installation require two speeds of rotation for the work. One of them is necessary for lifting, and another for exact stop of a cabin at a level of a floor. Now in these installations two speed motors with two separate windings are used. In this paper the opportunity of creation of the highly effective two-speed motor with pole-changing winding for lifts and elevator installations is considered. The industrial test results of motors with such windings are shown. The advantages of motors with pole-changing windings over conventional motors with two separate windings are given.

View PDFchevron_right
New elevator system constructed by multitranslator linear switched reluctance motor with enhanced motion quality
siamak masoudi

2020

In this work, a new elevator system created by a linear switched reluctance motor is presented. Unlike conventional linear motors, the proposed linear motor has more than one translator. Each phase in a translator generates a pulsing force; hence, the total generated force has noticeable ripple making it difficult to soft motion. In order to solve this problem, similar phases in different translators have been located in positions with specified distances together. As a result, similar force pulses would be shifted so that they can compensate together. An appropriate control strategy has been designed for the system, which can control the current, force, speed, and position simultaneously. A conventional proportional-integral controller and an adaptive fuzzy controller have been used to control the speed. In order to have a precise study, a prototype elevator system along with its control unit has been made and the obtained results have been compared with the simulation results. These results confirm that the proposed structure can significantly produce force and speed ripples.

View PDFchevron_right
Analysis and Fabrication of Remote Control Lifting Jack
Balkeshwar Singh

2015

With the increasing levels of technology, the efforts being put to produce any kind of work has been continuously decreasing. The efforts required in achieving the desired output can be effectively and economically be decreased by the implementation of better designs. Power screws are used to convert rotary motion into translatory motion. A screw jack is an example of a power screw in which a small force applied in a horizontal plane is used to raise or lower a large load. The principle on which it works is similar to that of an inclined plane. The mechanical advantage of a screw jack is the ratio of the load applied to the effort applied. The screw jack is operated by turning a lead screw. The height of the jack is adjusted by turning a lead screw and this adjustment can be done either manually or by integrating an electric motor. This research paper analyzes the modification of the existing motor screw jack by incorporating an electric motor in the screw in order to make load lift...

View PDFchevron_right
0 ) 2 6 -4 Learning Objectives Rotary synchronous motor for lift applications
mido sasa
View PDFchevron_right
Design and analysis of a double sided linear switched reluctance motor driver for elevator door
Mahir Dursun

In this study, an electromagnetic design of double sided linear switched reluctance motor (LSRM) is presented. It has been designed for driving an elevator door. The motor has tree phase and 6/4 poles. The motor's magnetic analysis was done as a 3 dimensional model. The parameters like magnetic forces, magnetic flux regarding to rotor positions and motor excitation currents were obtained statically with help of the finite element methods and Ansoft Maxwell 13.0 software. The motor's physical sizes were obtained as mathematically. Streszczenie. Przedstawiono projekt dwustronnego liniowego silnika reluktancyjnego przystosowanego do obsługi drzwi windy. Wykorzystując metodę elementu skończonego i program Ansoft Maxwell obliczono siłę magnetyczną, strumień magnetyczny dla różnych położeń wirnika oraz prąd zasilający. (Projekt i analiza dwustronnego silnika reluktancyjnego przystosowanego do obsługi drzwi windy). Introduction To In the places where there has been a heavy traffic ...

View PDFchevron_right
Design and Fabrication of Mechanical Lift for Transportation
GRD JOURNALS, Prof. R. K. Nanwatkar

Lift is a simple mechanical device used to raise element or object from ground level to a certain height to perform a specific work with maximum load and minimum efforts. This project describes the design as well as analysis of a mechanical scissor lift which works on the principle of screw jack. The design will be developed keeping in mind that the lift can be operated by mechanical means so that the overall cost of the scissor lift is reduced. Also such design can make the lift more compact and much suitable for medium scale work. Conventionally a scissor lift or jack is used for lifting a vehicle to change a tire, to gain access to go to the underside of the vehicle, to lift the body to appreciable height, and many other applications. But in this case along with lifting a vehicle we are also going to make an effort to move the vehicle to a short distance by incorporating roller mechanism. Finally, the analysis will be carried out in order to check the compatibility of the design values.

View PDFchevron_right
Linear motor for multi–car elevators: design and position measurement
Sandor Markon

2010

Multi-car elevator is an emerging technology consisting of two or more elevator cars moving independently in an elevator hoistway, which has become more appealing as building heights increase. In this paper, the design and drive methodologies for a linear motor driven multi-car elevator system with independently moving cars is introduced together with experimental results. Additionally, a safety method developed for the linear motor elevator and the conditions necessary for its proper operation are discussed.

View PDFchevron_right
Optimum Design of Traction Electrical Machines in Lift Installations
Ander Telleria San Torcuato, Xabier Hernandez, Xabier Arrasate

Improper operation of the traction machine of a lift installation causes energy waste, vibrations and noise. The design of the machine must be optimum if energy efficiency and comfort specifications have to be satisfied. The vibrations and noise frequency spectra of electrical machines present manifest peaks at certain frequencies, multiples of the fundamental electrical frequency, that depend on the machine topology and its rotation velocity. Changes in its topology or in its mechanical properties (geometry, size, materials…) must be done in order to reduce the magnitude of peaks at certain excitation frequencies or to locate the excitation frequencies far from the natural frequencies of the structure or the lift installation. Machine designers need tools to calculate their vibroacoustic response once a certain design has been proposed, so they can modify it before a prototype is built in case the response is not acceptable. Numerical and analytical models to calculate the vibroacoustic response of electrical machines have been developed and experimentally validated. In this paper, the authors summarise the state of the art in modelling the vibroacoustic performance of electrical machines and show some of the results obtained in their research work.

View PDFchevron_right

References (52)

  1. Local Government Department, Uniform Building By-Law 1984 (UBBL 1984) Amendments which is gazzetted according to the State Authority. 2021.
  2. H. Kamarudin, N. R. Muhamad Ariff, W. Z. Wan Ismail, A. F. Bakri, and Z. Ithnin, "Malaysian scenario on access and facilities for persons with disabilities: A literature review," MATEC Web of Conferences, vol. 15, 2014, doi: 10.1051/matecconf/20141501019.
  3. M. P. Shreelakshmi and V. Agarwal, "Trajectory Optimization for Loss Minimization in Induction Motor Fed Elevator Systems," IEEE Transactions on Power Electronics, vol. 33, no. 6, pp. 5160-5170, 2018, doi: 10.1109/TPEL.2017.2735905.
  4. C. Y. Lee and C. H. Lim, "Risk analysis and rescue operation for machine roomless lift: A case study," IEEE International Conference on Industrial Engineering and Engineering Management, vol. 2015-Janua, pp. 1265-1269, 2014, doi: 10.1109/IEEM.2014.7058841.
  5. D. Y. Kim, M. R. Park, J. H. Sim, and J. P. Hong, "Advanced Method of Selecting Number of Poles and Slots for Low-Frequency Vibration Reduction of Traction Motor for Elevator," IEEE/ASME Transactions on Mechatronics, vol. 22, no. 4, pp. 1554-1562, 2017, doi: 10.1109/TMECH.2017.2695059.
  6. K. Al-Kodmany, "Tall buildings and elevators: A Review of Recent Technological Advances," Buildings, vol. 5, no. 3, pp. 1070- 1104, 2015, doi: 10.3390/buildings5031070.
  7. B. Knežević, B. Blanuša, and D. Marčetić, "Model of elevator drive with jerk control," 2011, doi: 10.1109/ICAT.2011.6102118.
  8. H. Fan, K. Chau, C. Liu, and T. Ching, "Quantitative comparison of novel dual-PM linear motors for ropeless elevator system," 2018, doi: 10.1109/INTMAG.2018.8508648.
  9. H. S. Lim and R. Krishnan, "Ropeless elevator with linear switched reluctance motor drive actuation systems," IEEE Transactions on Industrial Electronics, vol. 54, no. 4, pp. 2209-2218, 2007, doi: 10.1109/TIE.2007.899875.
  10. M. Lu and R. Cao, "Comparative Investigation of High Temperature Superconducting Linear Flux-Switching Motor and High Temperature Superconducting Linear Switched Reluctance Motor for Urban Railway Transit," IEEE Transactions on Applied Superconductivity, vol. 31, no. 5, 2021, doi: 10.1109/TASC.2021.3054604.
  11. T. Hirayama, S. Yamashita, and S. Kawabata, "Design and Analysis of Linear Switched Reluctance Motor with Coreless HTS Excitation Windings for Ropeless Elevator," in ICEMS 2018 -2018 21st International Conference on Electrical Machines and Systems, 2018, pp. 1879-1884, doi: 10.23919/ICEMS.2018.8549217.
  12. S. G. Lee, S. A. Kim, S. Saha, Y. W. Zhu, and Y. H. Cho, "Optimal structure design for minimizing detent force of PMLSM for a ropeless elevator," IEEE Transactions on Magnetics, vol. 50, no. 1, 2014, doi: 10.1109/TMAG.2013.2277544.
  13. S. W. Oh, C. Lee, and W. You, "Gear Reducer Fault Diagnosis Using Learning Model for Spectral Density of Acoustic Signal," ICTC 2019 -10th International Conference on ICT Convergence: ICT Convergence Leading the Autonomous Future, pp. 1027- 1029, 2019, doi: 10.1109/ICTC46691.2019.8939913.
  14. S. Rangarajan and V. Agarwal, "Load Sensorless Novel Control Scheme for Minimizing the Starting Jerk and Energy of the PMSM Driven Gearless Elevators with Varying Stiction and Rotor Flux Linkage," 2019 IEEE Transportation Electrification Conference, ITEC-India 2019, 2019, doi: 10.1109/ITEC-India48457.2019.ITECIndia2019-225.
  15. G. Wang, Y. Wang, J. Xu, N. Zhao, and D. Xu, "Weight-Transducerless Rollback Mitigation Adopting Enhanced MPC with Extended State Observer for Direct-Drive Elevators," IEEE Transactions on Power Electronics, vol. 31, no. 6, pp. 4440-4451, 2016, doi: 10.1109/TPEL.2015.2475599.
  16. R. Anand and M. Mahesh, "Elevator drives energy analysis with duty loads and behavior in dynamic conditions," in 2016 IEEE International Conference on Emerging Technologies and Innovative Business Practices for the Transformation of Societies, EmergiTech 2016, 2016, pp. 133-138, doi: 10.1109/EmergiTech.2016.7737325.
  17. A. R. Rao and M. Mahesh, "Drives Analysis with Dynamic loads on Elevators and Interactive Study on Integration Systems," in IEEE International Conference on Power Electronics, Drives and Energy Systems, PEDES 2016, 2017, vol. 2016-Janua, pp. 1-6, doi: 10.1109/PEDES.2016.7914241.
  18. J. C. Hwang, C. S. Liu, and P. C. Chen, "Design of permanent-magnet synchronous gear motor with high efficiency for elevators," IEEE International Conference on Sustainable Energy Technologies, ICSET, pp. 205-210, 2012, doi: 10.1109/ICSET.2012.6357399.
  19. T. R. F. Neto and R. S. T. Pontes, "Design of a counterweight elevator prototype using a linear motor drive," Proceedings of IEEE International Electric Machines and Drives Conference, IEMDC 2007, vol. 1, pp. 376-380, 2007, doi: 10.1109/IEMDC.2007.382696.
  20. D. Wang, X. Du, D. Zhang, and X. Wang, "Design, optimization, and prototyping of segmental-type linear switched-reluctance motor with a toroidally wound mover for vertical propulsion application," IEEE Transactions on Industrial Electronics, vol. 65, no. 2, pp. 1865-1874, 2017, doi: 10.1109/TIE.2017.2740824.
  21. H. Seo, J. Lim, S. U. Park, and H. S. Mok, "A study on efficiency of magnetic levitation trains using linear induction motor by slip pattern," 2019 IEEE Energy Conversion Congress and Exposition, ECCE 2019, pp. 1635-1640, 2019, doi: 10.1109/ECCE.2019.8912945.
  22. Z. Huai, M. Zhang, Y. Zhu, A. Chen, and K. Yang, "Modeling for the Electromagnetic Dynamic Distortion Effect of the Induction- Based Electrodynamic Suspension Reaction Spheres," IEEE Transactions on Magnetics, vol. 57, no. 8, 2021, doi: 10.1109/TMAG.2021.3083700.
  23. A. Kumar, K. Gupta, H. Gupta, and M. Kuber, "Development of optimum double sided linear induction motor for military application," 2020, doi: 10.1109/PEDES49360.2020.9379392.
  24. H. T. Cho, Y. C. Liu, and K. A. Kim, "Short-primary linear induction motor modeling with end effects for electric transportation systems," in Proceedings -2018 International Symposium on Computer, Consumer and Control, IS3C 2018, 2018, pp. 338-341, doi: 10.1109/IS3C.2018.00092.
  25. W. Zhou, Z. Sun, Y. Mao, F. Cui, and H. Qian, "Analysis of the Motor Asymmetry Caused by the Static Longitudinal End Effect," 2021, doi: 10.1109/LDIA49489.2021.9505749.
  26. W. Liu, Z. Cui, W. Hao, and L. Song, "Effect of static longitudinal end effect on performance of arc linear induction motor," 2019, doi: 10.1109/ICEMS.2019.8922324.
  27. G. Lv, T. Zhou, and D. Zeng, "Influence of the Ladder-Slit Secondary on Reducing the Edge Effect and Transverse Forces in the Linear Induction Motor," IEEE Transactions on Industrial Electronics, vol. 65, no. 9, pp. 7516-7525, 2018, doi: 10.1109/TIE.2018.2795525.
  28. A. Z. Bazghaleh and E. F. Choolabi, "A New Approach for Non-Linear Time-Harmonic FEM-Based Analysis of Single-Sided Linear Induction Motor Incorporated with a New Accurate Method of Force Calculation," IEEE Transactions on Magnetics, vol. 57, no. 2, 2021, doi: 10.1109/TMAG.2020.3040720.
  29. H. Wang, J. Zhao, Y. Xiong, H. Xu, and S. Yan, "Optimal Design of a Short Primary Double-Sided Linear Induction Motor for Urban Rail Transit," World Electric Vehicle Journal, vol. 13, no. 2, 2022, doi: 10.3390/wevj13020030.
  30. Q. F. Lu and W. H. Mei, "Recent development of linear machine topologies and applications," CES Transactions on Electrical Machines and Systems, vol. 2, no. 1, pp. 65-72, 2020, doi: 10.23919/tems.2018.8326452.
  31. D. Zeng, B. Zhang, X. Wang, P. Yang, Q. Ge, and Y. Li, "Analysis of Traction Characteristics in Single-sided Linear Induction Motors with Composite Secondary Considering Magnetic Saturation and Hysteresis," 2021 13th International Symposium on Linear Drives for Industry Applications, LDIA 2021, 2021, doi: 10.1109/LDIA49489.2021.9505839.
  32. A. Zare-Bazghaleh, E. Fallah-Chulabi, and S. H. Shahalami, "Force calculation with complete modeling of end-effect in single- sided linear induction motors," 7th Power Electronics, Drive Systems and Technologies Conference, PEDSTC 2016, pp. 19-23, 2016, doi: 10.1109/PEDSTC.2016.7556831.
  33. L. B. Xaxa, A. Kumar, R. K. Srivastava, R. K. Saket, and B. Khan, "Design Aspects Thermal Characteristics of Single-Sided Linear Induction Motor for Electromagnetic Launch Application," IEEE Access, vol. 10, pp. 72239-72252, 2022, doi: 10.1109/ACCESS.2022.3188673.
  34. X. Liu, X. Zhu, J. Cai, L. Gao, X. Peng, and Z. Cui, "Design on Double-sided Linear Induction Motor with Varying Pole Pitch for the Electromagnetic Catapult," 2021 13th International Symposium on Linear Drives for Industry Applications, LDIA 2021, 2021, doi: 10.1109/LDIA49489.2021.9505955.
  35. S. E. Abdollahi, M. Mirzayee, and M. Mirsalim, "Design and Analysis of a Double-Sided Linear Induction Motor for Transportation," IEEE Transactions on Magnetics, vol. 51, no. 7, 2015, doi: 10.1109/TMAG.2015.2407856.
  36. V. W. Nage and S. M. Shinde, "An elevator driven by Single-Sided Linear Induction Motor (SLIM)," Proceedings of 2016 International Conference on Advanced Communication Control and Computing Technologies, ICACCCT 2016, pp. 376-379, 2017, doi: 10.1109/ICACCCT.2016.7831665.
  37. Q. Lu, Y. Yao, Y. Ye, and J. Dong, "Research on ropeless elevator driven by PMLSM," 2016, doi: 10.1109/EVER.2016.7476386.
  38. X. Huang, J. Liang, B. Zhou, C. Zhang, L. Li, and D. Gerada, "Suppressing the Thrust Ripple of the Consequent-Pole Permanent Magnet Linear Synchronous Motor by Two-Step Design," IEEE Access, vol. 6, pp. 32935-32944, 2018, doi: 10.1109/ACCESS.2018.2847237.
  39. Z. Liu, X. Wang, B. Du, X. Xu, S. Ji, and C. Xiao, "Performance Optimization Analysis of PMLSM with Novel Composite Magnetic Slot Wedge," 2019, doi: 10.1109/ICEMS.2019.8921716.
  40. T. Dong, R. Fu, B. Zhang, B. Peng, and X. Wei, "Analysis of Permanent Magnet Linear Synchronous Motor Made by Oriented Silicon Steel Sheet," IEEE Transactions on Industry Applications, vol. 59, no. 3, pp. 3332-3340, 2023, doi: 10.1109/TIA.2023.3253816.
  41. Z. Zhang, M. Luo, J. A. Duan, and B. Kou, "Performance Analysis of Double-Sided Permanent Magnet Linear Synchronous Motor with Quasi-Sinusoidal Ring Windings," IEEE Transactions on Energy Conversion, vol. 35, no. 3, pp. 1465-1474, 2020, doi: 10.1109/TEC.2020.2981634.
  42. Z. Sun, K. Watanabe, and X. Xu, "Influence of Slot and Pole Number Combinations on PMLSM with Consequent Pole," 2021, doi: 10.1109/LDIA49489.2021.9505983.
  43. X. Xu, Z. Sun, B. Du, and L. Ai, "Pole optimization and thrust ripple suppression of new halbach consequent-pole PMLSM for ropeless elevator propulsion," IEEE Access, vol. 8, pp. 62042-62052, 2020, doi: 10.1109/ACCESS.2020.2984281.
  44. D. Wang, X. Wang, and X. F. Du, "Design and Comparison of a High Force Density Dual-Side Linear Switched Reluctance Motor for Long Rail Propulsion Application with Low Cost," IEEE Transactions on Magnetics, vol. 53, no. 6, 2017, doi: 10.1109/TMAG.2017.2659804.
  45. X. Li, F. Liu, W. Jiang, H. Jin, M. Li, and Q. Wang, "Design and Control of a Transverse Flux Linear Switched Reluctance Machine for Rail Transit Application," IEEE Access, vol. 10, pp. 43175-43186, 2022, doi: 10.1109/ACCESS.2022.3169888.
  46. M. Vatani and M. Mirsalim, "Comprehensive Research on a Modular-Stator Linear Switched Reluctance Motor with a Toroidally Wound Mover for Elevator Applications," in 2019 10th International Power Electronics, Drive Systems and Technologies Conference, PEDSTC 2019, 2019, pp. 61-66, doi: 10.1109/PEDSTC.2019.8697241.
  47. A. Lachheb, J. Khediri, and L. El Amraoui, "Modeling and performances analysis of switched reluctance linear motor for sliding door application," 2018 15th International Multi-Conference on Systems, Signals and Devices, SSD 2018, pp. 1336-1341, 2018, doi: 10.1109/SSD.2018.8570402.
  48. N. A. M. Nasir, F. A. Shukor, N. M. Zuki, and R. N. F. K. R. Othman, "Design of the segmented-type switched reluctance linear synchronous motor (SSRLSM) for domestic lift application," Progress In Electromagnetics Research C, vol. 108, pp. 13-22, 2021, doi: 10.2528/PIERC20110205.
  49. D. Wang, C. Shao, and X. Wang, "Performance Analysis and Design Optimization of an Annular Winding Bilateral Linear Switch Reluctance Machine for Low Cost Linear Applications," IEEE Transactions on Applied Superconductivity, vol. 26, no. 7, 2016, doi: 10.1109/TASC.2016.2595584.
  50. T. Higuchi, Y. Yokoi, T. Abe, N. Yasumura, Y. Miyamoto, and S. Makino, "Design analysis of a segment type linear switched reluctance motor," 2017, doi: 10.23919/LDIA.2017.8097226.
  51. S. Masoudi, H. Mehrjerdi, and A. Ghorbani, "New elevator system constructed by multi-translator linear switched reluctance motor with enhanced motion quality," IET Electric Power Applications, vol. 14, no. 9, pp. 1692-1701, 2020, doi: 10.1049/iet- epa.2019.0996.
  52. S. Masoudi, M. R. Feyzi, and M. B. B. Sharifian, "Force ripple and jerk minimisation in double sided linear switched reluctance motor used in elevator application," IET Electric Power Applications, vol. 10, no. 6, pp. 508-516, 2016, doi: 10.1049/iet- epa.2015.0555.

Related papers

Design of the Segmented-Type Switched Reluctance Linear Synchronous Motor (SSRLSM) for Domestic Lift Application
Nur Ashikin Mohd Nasir

Progress in Electromagnetics Research C, 2021

This paper proposes an SRLSM with segmental stator pole. The segmented SRLSM which is known as SSRLSM was designed for domestic lift application. The SSRLSM was designed to fulfill the design target requirement where the lift must be able to transport a maximum 200 kg payload. This payload requires a motor with more than 2000 N thrust force at rated power of 1.5 kW. The rated current is 2.5 A. However, for the excitation current, the maximum current is taken twice of the rated current which is 5.0 A. The design of the SSRLSM was completed in two stages. The first stage is to design the stator pole length, lst, while the second stage is to design the stator pole thickness, tst. The designed models were simulated with FEM software. The simulation results show that the highest thrust produced in first stage is 6773 N. The thrust is produced by the model with stator pole length, lst, of 120 mm. Meanwhile, in the second stage, the model with the stator pole thickness, tst, of 20 mm produ...

View PDFchevron_right
Analysis of linear motor with symmetrical EMF vector for household elevator application
International Journal of Power Electronics and Drive Systems

International Journal of Power Electronics and Drive System, 2023

Linear permanent magnet synchronous motor (LPMSM) has emerged as a viable alternative to other linear motors for higher thrust lifting action. With the advancement of permanent magnets, LPMSM could contribute to energy conversation while also being suitable for applications requiring higher thrust, such as elevator. However, because the existing LPMSM is larger in size, it requires more space to be equipped with a household elevator. To address this issue, a new LPMSM with increased thrust capability has been proposed. The new LPMSM is modelled and analyzed in terms of back EMF and force in this paper. For improved performance, a symmetrical EMF vector is applied to the new LPMSM. In terms of back EMF and force, 4 LPMSM models are studied. According to the results, 6 slot 4 pole has the highest back EMF when compared to the others. As a suitable combination of slot and pole, a symmetrical EMF vector is the suggested LPMSM at the end of this research.

View PDFchevron_right
Design and Implementation of a Linear Motor for Multicar Elevators
Sandor Markon

2010

Abstract The multicar elevator system is a revolutionary new technology for high-rise buildings, promising outstanding economic benefits, but also requiring new technology for propulsion, safety, and control. In this paper, we report on experimental results with new components for linear-motor-driven multicar elevators. We show that linear synchronous motors with optimized design and with our new safety and control system can be considered as core components of a new generation of elevator systems.

View PDFchevron_right
Design & Development of Automatic Lifting System in Automobile
International Research Group - IJET JOURNAL
View PDFchevron_right
Comparative Study on Different Variable Reluctance Linear Machine Structures (With/Without Permanent Magnets)
Dan-Cristian Popa

2007

View PDFchevron_right

Related topics

  • Linear Motors
  • Artificial Lift Systems
    • 580 California St., Suite 400
    San Francisco, CA, 94104
    © 2025 Academia. All rights reserved